Challenger MT455E, MT465E, MT475E Tractor Service Manual

Challenger MT455E, MT465E, MT475E Tractor Repair Workshop Manual

Manual for: AGCO Challenger MT400E Series Tractor

Format: PDF

Book Number: ACT0026660

English

Issued May 2016

Challenger MT455E, MT465E, MT475E Tractor Workshop Manual : 1376 Pages

Challenger MT400E Series Manual TABLE OF CONTENTS

• Introduction
• Separation of assemblies
• Engine
• Clutch
• Gearbox
• Rear Axle
• Power Take off
• Front Axle
• Hydraulics
• Electricity
• Electronics
• Operator Environment
• Accessories
• Services Tools

This genuine factory repair guide is your all-in-one solution for maintaining top performance. It covers every aspect of repair and maintenance, including lubrication charts, system overviews, and troubleshooting codes. Each section is logically arranged for quick access to vital information.

Whether you’re replacing components or fine-tuning performance, the detailed instructions make complex repairs simple. Trusted by dealerships and field technicians, this manual ensures every repair follows official standards. Keep your machine in prime working condition, avoid costly downtime, and gain confidence knowing your repairs are backed by the manufacturer’s expertise.

1. Introduction

1.1 General

1.1.1 Using the manual
1.1.2 General specifications
1.1.2.1 MT400E AutoPower IV tractors
1.1.2.2 MT400E AutoPower VI tractors
1.1.2.3 MT400E TechStar CVT tractors
1.1.3 Forward speeds
1.1.3.1 Forward speed with AutoPower IV 40 kph transmission and 18.4R38 tires
1.1.3.2 Forward speed with AutoPower IV 40 kph transmission and 20.8R38 tires
1.1.3.3 Forward speed with AutoPower VI 40 kph ECO transmission and 20.8R38 tires
1.1.3.4 Forward speed with AutoPower VI 50 kph transmission and 20.8R38 tires
1.1.3.5 Forward speed for all models with transmission in TechStar CVT mode
1.1.4 Dimensions and weights
1.1.5 Attachment points
1.1.5.1 Attachment points: MT455E / MT465E / MT475E AutoPower IV / AutoPower VI models without front linkage
1.1.5.2 Attachment points: MT455E / MT465E / MT475E AutoPower IV / AutoPower VI models with front linkage
1.1.5.3 Attachment points: MT485E / MT495E / AutoPower IV / AutoPower VI models without front linkage
1.1.5.4 Attachment points: MT485E / MT495E / AutoPower IV / AutoPower VI models with front linkage
1.1.5.5 Attachment points: MT465E / MT475E / MT485E / MT495E / TechStar CVT models without front linkage
1.1.5.6 Attachment points: MT465E / MT475E / MT485E / MT495E / TechStar CVT models with front linkage
1.1.6 Capacities
1.1.7 Conversion table
1.1.8 Retaining compounds and sealing products
1.1.9 Tightening torques
1.1.9.1 Tightening torques for screws and nuts
1.1.9.2 Tightening torques for hydraulic unions

1.2 Adjustments, bleeding and calibrations

1.2.1 Bleed operations: TechStar CVT – Assisted brake master cylinders
1.2.1.1 Charge connector
1.2.1.2 Pressure connector
1.2.1.3 Bleed screw locations
1.2.1.4 Procedure for bleeding the assisted braking system
1.2.2 Bleed operations: AutoPower IV / AutoPower VI – Assisted brake master cylinders
1.2.2.1 Charge connector
1.2.2.2 Pressure connector – Load Sensing system
1.2.2.3 Pressure connector – Open Center system
1.2.2.4 Bleed screw locations
1.2.2.5 Procedure for bleeding the assisted braking system
1.2.3 Bleed operations: AutoPower IV / AutoPower VI – High-pressure braking
1.2.3.1 Bleed screw locations
1.2.3.2 Procedure for bleeding the high-pressure braking system

Challenger MT455E, MT465E, MT475E Tractor Service Manual